Gutter and downspout repair in Portland
Leaking seams, sagging runs, hangers pulled out of the fascia and downspouts that dump at the foundation. We repair Portland gutters so they carry water where it belongs again.
Gutter repair in Portland usually means resealing leaking corners and end caps, replacing pulled or broken hangers, re-pitching sagging runs so water reaches the outlet, and clearing, reattaching or replacing damaged downspouts. Most gutters with sound metal can be repaired for a fraction of replacement cost, especially when the fascia behind them is still solid.
Gutters rarely fail all at once. A corner starts to drip, a hanger lets go after a heavy load of wet needles, a downspout elbow gets knocked loose by a lawn mower. Each problem is small, but together they send water onto your siding, into your crawlspace and over the edge of your porch steps all winter long.
When the gutter itself is in decent shape, repair is the sensible fix. We reseal joints from the inside with gutter sealant, add new hidden hangers where old spikes have pulled out, lift and re-pitch runs that hold water, and reconnect or replace downspout sections. Most repairs take a few hours, and the gutters are back to work by the next rain.
We also look at why the problem happened. A gutter that keeps sagging in the same spot may be fastened to rotted fascia. A downspout that keeps clogging may be too small for the roof above it. Fixing the cause is what keeps you from calling us back for the same repair again next winter.
Repair or replace: what fits your gutters?
We match the fix to the condition of the metal and the fascia behind it.
Spot repair and reseal
Best when only a few joints leak and the gutter is otherwise solid. Resealing corners and outlets is quick and affordable, and it extends the life of a sound aluminum gutter by several seasons.
Re-hang with new hangers
For gutters that sag or pull away but have no holes or major dents. New hidden hangers and corrected pitch make them work like new without replacing the metal.
Section replacement
When one run is dented, rusted through or badly bent, we replace that section with new seamless gutter formed to length, matched as closely as possible to the existing profile and color.
Full gutter replacement
When most runs leak, sag or are badly undersized, repairs only buy time. New seamless gutters sized for the roof make more sense, and we explain that honestly instead of patching again.
Which gutter problems can be repaired instead of replaced?
These are the gutter troubles we fix most often around Portland.
Dripping corners and end caps
Mitered corners and end caps are the weak points on any gutter. When the old sealant dries and cracks, water drips steadily at those spots. Cleaning them out and resealing from the inside usually stops the leak.
Sagging sections that hold water
A gutter that dips in the middle collects standing water, needles and silt. The extra weight pulls it lower over time. Re-hanging the run with new hangers and the correct pitch gets water flowing again.
Hangers pulled out of the fascia
Spike and ferrule hangers back out as the wood softens and the gutter swings forward. We replace them with screw-in hidden hangers, which grip better and hold the gutter tight to the board.
Downspouts loose or crushed
Downspouts get bumped, bent and pulled apart at the elbows. A crushed section restricts flow and a loose one dumps water against the wall. We replace damaged pieces and fasten them with proper straps.
Water pooling at the foundation
If downspouts empty right at the house, water soaks the soil along the foundation. Extensions, splash blocks or a redirected outlet carry it far enough away to keep crawlspaces drier.
Overflow at the same spot every storm
When one section always overflows, the outlet may be clogged, the run may slope the wrong way or a valley may be dumping more water than the gutter can take. Each has a different fix.
How we track down and fix gutter problems
Clean out and flush the system
We clear needles, leaves and silt from every gutter and flush each downspout. A clean system shows the real problems, such as a leaking seam or a low spot, instead of symptoms caused by clogs.
Check pitch and fastening
We check each run with a level for proper fall toward the outlet and test every hanger. Loose and missing hangers get marked, along with any spot where the fascia behind feels soft.
Reseal seams, corners and outlets
Leaking joints get scraped clean, dried and sealed from inside with gutter sealant. Corners with gaps may get a new rivet or a strip of aluminum flashing before sealing.
Re-hang and re-pitch sagging runs
We lift sagging sections, install hidden hangers about every two feet into solid wood and set the gutter to drain steadily toward its downspout without visible tilt from the street.
Repair or replace downspouts
Crushed or split downspout sections and elbows get replaced with matching pieces. We strap them firmly to the wall and add extensions so water discharges well away from the foundation.
Test with water before leaving
We run water through every repaired section to confirm it drains to its outlet and the seams stay dry, then show you what we fixed and anything that should be watched.
Materials for gutter & downspout repair come from manufacturers such as Malarkey, GAF, Owens Corning, CertainTeed, Carlisle and Velux, chosen for the job rather than the logo.
What does gutter repair cost in Portland?
Most gutter repairs are priced per job, with parts added as needed. Here is what Portland homeowners commonly pay in 2026.
| Work | Typical Portland range |
|---|---|
| Reseal leaking corners and end capsper job | $135 to $315 |
| Re-hang sagging gutter runper run | $185 to $465 |
| Downspout section or elbow replacementper downspout | $95 to $265 |
| Gutter section replacementper section | $315 to $845 |
| Clean, flush and minor repairsper home | $215 to $485 |
These figures show where most Portland gutter repairs land, not what yours will cost. We price your job after a close look at the gutters and a written estimate.
What moves the price:
- Number of leaking joints
- Length of sagging runs
- Height and stories
- Fascia condition
- Parts and color matching
Why Portland gutters break down the way they do
Our gutters work hard from October through May, and most of the damage we repair comes from weight. Wet Douglas fir needles and bigleaf maple leaves pack into a gutter like a sponge, and that load pulls hangers out of the fascia, especially on older homes in Concordia, Woodstock and Arbor Lodge where the boards behind the gutters have had decades of weather.
Cold snaps add another stress. When ice formed during the January 2024 storm, gutters across Gresham, Troutdale and the east side bent under the weight, and some still sag at the corners. On hillside homes in Southwest Hills, long downspouts run down tall walls and come loose at the brackets. Each of these calls for its own repair.
Why our gutter repairs hold through the wet season
We fix the cause, not just the drip
If a gutter sags because the fascia is rotten, or overflows because a valley dumps too much water, we tell you and fix that too, so the same repair does not come back.
Screw-in hangers into solid wood
We use hidden hangers fastened with screws into sound fascia instead of spikes that work loose. That is the main reason our re-hung runs stay put under wet needle loads.
Water tested before we leave
Every repair gets a hose test so you see the water reach the downspout and the seams stay dry, instead of finding out during the next storm.
Gutter & Downspout Repair questions from Portland homeowners
Is it worth repairing old gutters on a Portland home?
If the aluminum is sound and only a few joints leak or a run sags, repair is usually worth it. If most runs leak, the gutters are badly undersized or the metal is dented and corroded, new seamless gutters often cost less over time than repeated repairs.
Why do my Portland gutters keep pulling away from the house?
Usually the hangers are spikes that have loosened in softening fascia, or the gutter is carrying heavy wet needle loads. We replace them with screw-in hidden hangers set into solid wood and replace rotted fascia where needed so the gutter stays tight to the house.
How do you fix a leaking gutter corner in Portland?
We clean and dry the corner, remove the old sealant, check that the miter fits tightly and add rivets or a flashing strip if there is a gap. Then we seal it from the inside with gutter sealant and water test it. Most corner repairs last for years.
Can you repair downspouts that clog with fir needles in Portland?
We clear the clog and look at why it happened. Common causes are small 2 by 3 inch downspouts, tight elbows or crushed sections. Upgrading to 3 by 4 inch downspouts or adding a gutter guard often stops repeat clogs under heavy Douglas fir cover.
Do you repair gutters bent by ice or snow in Portland?
Yes. Ice can bend gutters and pull hangers out at the corners, as many Portland homeowners saw after the January 2024 storm. We straighten what can be straightened, replace bent sections and re-hang the run with closer hanger spacing for better support.
Where we do this work most
We cover the whole metro. These are the places we are on roofs most often:
Related roofing services
Seamless Gutter Installation
Seamless aluminum gutters formed on site to fit your Portland home, sized for our long rainy season and fitted with downspouts that move water away...
Gutter Guards
Not every gutter guard can stop Douglas fir needles. We fit Portland homes with guards matched to the trees overhead, so gutters keep flowing through...
Fascia & Soffit Repair
Soft fascia behind the gutter, peeling soffit paint or birds nesting in the eaves usually means water has been getting past your roof edge. We...
Roof Maintenance
A regular tune-up keeps a Portland roof ahead of the rain. We clear debris, renew sealant, check every boot and flashing and flush gutters on a...
Related reading
Fall Roof Checklist Before Portland Rain
September is the last reliable dry window before Portland settles into months of rain. Use this room by room checklist to find the small roof problems that turn into winter leaks.
Gutters for Portland Homes Under Douglas Firs
Douglas fir needles are small, sharp and endless, and they clog gutters in ways leaves never do. Here is how Portland homeowners can size, guard and clean gutters to keep water moving under big firs.
Need gutter & downspout repair in Portland?
Call and tell us what you are seeing. We answer 24/7 and can usually talk you through the next step on the first call.